Kit H0 (1:87)                                                                                                              L 210 x W 150 x H 145mm

Versatile factory hall with covered loading ramp on one long side and 2 large gates on one cross side. With large skylight and internal steel supporting framework.

The Carl Urbach steelworks, a hammer mill with its own railway siding, was located in Kräwinklerbrücke/Radevormwald. Hall 2 is the addition to our item 17004 Stahlwerk C. Urbach. A crane bridge, art. 17005, also belonged to the works.

Kit H0 (1:87)                                                                                                            L 180 x H 14 mm                                                                                                  Typical swedish picket fence with gates, in Faluröd.

Kit H0 (1:87). Half-timbered building with a coach room, horse stable and space for carriages. One of the parking spaces is designed as a passage. 

Size in mm: L 190 x W 77 x H 86

Kit H0 (1:87)                                                           warehouse building with loading ramp and attached staircase                                                                          Dimensions in mm: L 243 x W 85 x H 142

Workshop or warehouse building with loading ramp and attached staircase. The back front is smoothly plastered, front and side front are tiled, 1st and 2nd floors are timber-framed. The staircase can be attached to the side or front (or omitted).  This type of construction was widely used. Our prototype was in Wuppertal, similar buildings can be found all over Germany. The kit fits perfectly to our other storage buildings. ( Art No 17079/17078)

Kit H0 (1:87), dimensions in mm: Ø 450 (+ lift) x H 150

Extends the basic kit art. 17051 with 1 ring.Gasometer based on model photos of the Hansa coking plant, type MAN
A so-called disc gas container, the gas pressure was obtained by a movable sealing disc, which was on the gas. The sealing apron was pressed with tension springs and weights to the outer wall of the container. To seal the apron was covered about one meter high with an oily sealing liquid. For air circulation and pressure equalization, there were ventilation openings at the upper edge of the roof hood. Our kit is also available as a semi-relief Art. 17053.

available from august 2022

Kit H0 (1:87)                                                                                                             L 53 x W 43 x H 28mm                                                                                         transformer house, brick

With fine openwork ventilation grids, small building suitable for industrial, railway and urban areas.

L 53 x W 43 x H 28mm

Another small, single-storey extension, simply plastered, for our town house program, part of which serves as a garage. Also suitable for railway systems or industrial areas.
Dimensions in mm L 90 x W 45 x H 42

Kit H0 (1:87)                                                                                                                        L 135 x W 65 x H 63mm

In this fenced off safety area possibly dangerous goods, liquids or gases could be cooled.

The floor channel for the pipes connecting the units is covered with openwork grids and can therefore also be displayed open. The fence with extremely fine wire mesh is also available as single kit Art. 40439

Kit H0 (1:87)                                             Substructure with brick facade and steel frame                    Element 1/2 wall window in the middle 6 pieces                                                  Dimensions per element: L 37,5 x W 8 x H 37.5 mm

An article of our modular system BKS 

you can find a planning aid here

Fits e.g. well in the depot or on the shunting tracks of a station, due to the very narrow design and the doors on the front sides, it is well suited to be used between two tracks, as a material store for lubricants, sand and lanterns or as a lounge for employees place. Finely engraved wooden structure. Dimensions in mm L 65 x W 22 x H 33

Fits e.g. well in the depot or on the shunting tracks of a station, due to the very narrow design and the doors on the front sides, it is well suited to be used between two tracks, as a material store for lubricants, sand and lanterns or as a lounge for employees place. Finely engraved 3D brick structure. Dimensions in mm L 65 x W 22 x H 33

Kit 0 (1:43,5). For the transport of glowing steel blocks from the steelworks to further processing plants, such as a rolling mill. Removable cover.

Size in mm: L 140 x W 66 x H 80